Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
三浦 靖史*; 鈴木 賢治*; 諸岡 聡; 菖蒲 敬久
Quantum Beam Science (Internet), 8(1), p.1_1 - 1_14, 2024/03
Probabilistic fracture mechanics (PFM) is expected as a reasonable structural integrity assessment method for nuclear components such as piping, whose main degradation phenomenon is stress corrosion cracking (SCC). Some input parameters are necessary for PFM analysis, and welding residual stress is one of the most important parameters because welding residual stress affects SCC initiation and propagation. Recently, a double exposure method (DEM) with synchrotron X-ray has been proposed, and the method is an expected candidate for the measurement of welding residual stress with a high spatial resolution. In this paper, the DEM was applied to measure the residual stress of the plate specimen, which was cut from the welded pipe using electrical discharge machining, and detailed stress maps under a plane stress state were obtained. Furthermore, the residual stress distributions of the welded pipe under a triaxial stress state were also evaluated using neutron diffraction. From these results, the method for obtaining a detailed stress map of the welded pipe by the complementary use of high-energy synchrotron radiation X-rays and neutrons was proposed.
山崎 泰広*; 篠宮 啓介*; 奥村 忠晴*; 鈴木 賢治*; 菖蒲 敬久; 中村 唯我*
Quantum Beam Science (Internet), 7(2), p.14_1 - 14_12, 2023/05
The suspension plasma spray (SPS) technique has attracted attention because of its various microstructures, which can be achieved by mixing submicron spray particles with a solvent to form a suspension. Thermal barrier coatings (TBCs) with a columnar structure, which might achieve high strain tolerance, can be obtained using the SPS technique. In this study, the internal stress distribution of the SPS-TBC with different columnar structures was evaluated by hybrid measurement using high-energy synchrotron X-ray diffraction analysis and laboratory low-energy X-rays. The effect of microstructure on the internal stress distribution of the SPS-TBC was discussed on the basis of the experimental results. In addition, the in-plane internal stress was decreased by decreasing the column diameter. The thin columnar microstructure of the SPS-TBC has superior strain tolerance. The internal stresses in the column of the SPS-TBC are periodic decrements caused by stress relaxation in porous layers.
鈴木 賢治*; 三浦 靖史*; 城 鮎美*; 豊川 秀訓*; 佐治 超爾*; 菖蒲 敬久; 諸岡 聡
材料, 72(4), p.316 - 323, 2023/04
Residual stresses in small-bore butt-welded pipe of austenitic stainless steel have never been measured. It is difficult to obtain a detailed residual stress map of the root welded part, because the gauge volume in neutron diffraction is large. The stress evaluation of the welded part by synchrotron X-rays was also difficult due to the dendritic structure. In this study, a double exposure method (DEM) with high-energy synchrotron X-rays was applied to measuring the details of the residual stress of the welded part, and we succeeded in obtaining the detailed axial and radius stress maps of the root welded part of the plate cut from the welded pipe, though the stress map was under the plane stress condition. The hoop stress map of the butt-welded pipe was obtained using the strain scanning method with neutrons under the triaxial stress state. The axial and radius stress maps under triaxial stress state were made up using the complementary use of the synchrotron X-ray and neutron. As a result, the detailed stress maps of the root welded part of the butt-welded pipe were obtained. The obtained map sufficiently explained the initiation and propagation of SCC.
鈴木 賢治*; 倉 己萌*; 三浦 靖史*; 城 鮎美*; 豊川 秀訓*; 佐治 超爾*; 梶原 堅太郎*; 菖蒲 敬久
材料, 71(12), p.1005 - 1012, 2022/12
放射光X線を用いてオーステナイト系ステンレス鋼の溶接部応力測定を実施した。溶接部のX線応力測定の課題は、回折スポットが半径方向および円周方向に広がることである。当該課題を解決するために溶接部からなる角棒の曲げひずみを70keVの放射光単色X線と二重露光法を用いて測定した。2次元検出器からの回折パターンは、テクスチャーマテリアルからのパターンのような鋭い弧を示した。当該結果より回折プロファイルを円周方向の回折強度を積分から取得し、回折角度は二重露光法を使用して決定した。その結果、溶接部の残留応力分布を測定することに成功した。
鈴木 賢治*; 山田 みなみ*; 城 鮎美*; 菖蒲 敬久; 豊川 秀訓*; 佐治 超爾*
材料, 71(4), p.347 - 353, 2022/04
30keVのシンクロトロン放射光X線による二重露光法(DEM)を用いたアルミ合金の残留応力に関してはすでに成功している。しかしながら、高エネルギー放射光X線の領域でDEMは未だ試されていない。本研究では、約70keVのシンクロトロンX線で焼きばめ材の応力を測定した。検出器としては、CdTeピクセル検出器とDDC検出器を用いた。SUS304の焼きばめ試験片の粒径は、43mのやや粗大な粒であり、回折環は斑点状であった。やや粗大粒であったが、DEMによって焼きばめ試験片の応力を測定することができた。その結果、DEMは粗大粒の応力測定に優れていることがわかる。また、検出器間距離を大きくすることが精度をよくする効果がある。他方、検出位置を増やしても精度改善効果はなかった。
高橋 温*; 千葉 美麗*; 棚原 朗*; 相田 潤*; 清水 良央*; 鈴木 敏彦*; 村上 忍*; 小荒井 一真; 小野 拓実*; 岡 壽崇; et al.
Scientific Reports (Internet), 11(1), p.10355_1 - 10355_11, 2021/05
被引用回数:6 パーセンタイル:41.49(Multidisciplinary Sciences)The Fukushima-Daiichi Nuclear Power Plant (FNPP) accident released substantial amounts of radionuclides into the environment. We collected 4,957 deciduous teeth, from children living in Fukushima and reference prefectures. Radioactivity was detected in most of the teeth examined and was attributed to the presence of natural radionuclides, including K and daughter nuclides in U and Th series. Additionally, artificial radionuclides, Sr and Cs, were detected in the teeth obtained from children from Fukushima and the reference prefectures. However, these radionuclides were not believed to have originated from the FNPP accident. Because the teeth examined in the present study were formed before the FNPP accident occurred, the aforementioned findings may serve as important control data for future studies regarding the radioactivity of teeth formed after the FNPP accident.
鈴木 賢治*; 城 鮎美*; 豊川 秀訓*; 佐治 超爾*; 菖蒲 敬久
Quantum Beam Science (Internet), 4(3), p.25_1 - 25_14, 2020/09
粗大粒で構成される材料の2次元回折パターンはリング状とはならずスポット状となるため、従来の回折計と0次元検出器を利用したひずみスキャンニング法では応力評価が困難である。この課題を解決するために2次元検出器を利用した2重露光法を提案した。本研究ではこの技術を白色X線に対して適用するための技術開発を行った。粗大粒で構成される材料に白色X線を照射すると得られる回折はラウエスポットとなる。そこで検出するエネルギーを制限できるCdTeピクセル2次元検出器の開発とそれを利用した応力評価を行った。その結果、オーステナイト系ステンレス鋼を供試材とする曲げ試験片に対して、ほぼ理論値通りのひずみ分布を計測することに成功した。今後、当該技術の向上を図り、実機材料に適用していきたいと考えている。
Sun, X. H.*; Wang, H.*; 大津 秀暁*; 櫻井 博儀*; Ahn, D. S.*; 合川 正幸*; 福田 直樹*; 磯部 忠昭*; 川上 駿介*; 小山 俊平*; et al.
Physical Review C, 101(6), p.064623_1 - 064623_12, 2020/06
被引用回数:5 パーセンタイル:52.72(Physics, Nuclear)理化学研究所RIビームファクトリーにて逆運動学法を使用し、核子当たり168MeVの陽子, 重陽子, 炭素イオン入射によるXeのスポレーションおよびフラグメンテーション反応からの同位体生成断面積を測定した。炭素イオンの場合は全運動エネルギーが高くなるため、質量数の小さな同位体の生成断面積が大きくなった。また、今回新たに測定されたデータを以前により高い入射エネルギーで測定されたデータと比較することで、同位体生成断面積の入射エネルギー依存性を調査した。さらに、測定データをPHITS, SPACS, EPAX, DEURACSの計算値と比較した。本研究で測定したデータは、理論計算の良いベンチマークになると考えられる。
Bae, S.*; Jee, H.*; Suh, H.*; 兼松 学*; 城 鮎美*; 町田 晃彦*; 綿貫 徹*; 菖蒲 敬久; 諸岡 聡; Geng, G.*; et al.
Construction and Building Materials, 237, p.117714_1 - 117714_10, 2020/03
被引用回数:15 パーセンタイル:67.1(Construction & Building Technology)Although the atomistic structure and the deformation characteristics of calcium silicate hydrates (C-S-H) are of primary interest in cement chemistry, they have not been fully investigated. In this study, pair distribution function (PDF) analysis was conducted on a 53-year-old fully hydrated tricalcium silicate (CS) paste using in situ synchrotron high-energy X-ray scattering to probe the atomic structural deformation of C-S-H under external loading. The results were compared with those from our previous PDF study of a 131-day-old CS paste in order to elucidate the effect of aging on the mechanical characteristics of C-S-H. Three different strains measured by the strain gauge, by the lattice shifts (d-spacing) in the reciprocal space, and by the shift of the interatomic distance (r) in the real space were compared. In the range of r 20 , where most of the information was derived from C-S-H, the 53-year-old CS paste had a higher overall elastic modulus (18.3 GPa) and better resistance to compressive stress than the 131-day-old CS paste (elastic modulus: 8.3 GPa). Moreover, it was found that the macroscopic strains of the 53-year-old CS paste were presumably induced by mechanical deformation such as microcracks at the macroscale. The results provide experimental evidence for the atomistic and mesoscale mechanical behavior of C-S-H in the early and late ages.
鈴木 竜平*; 谷 幸則*; 内藤 博敬*; 宮田 直幸*; 田中 万也
Catalysts, 10(1), p.44_1 - 44_15, 2020/01
被引用回数:10 パーセンタイル:40.35(Chemistry, Physical)本研究では、マンガン酸化菌KR21-2株を用いて形成させたマンガン酸化物に対してpH6のCr(NO)水溶液を用いて一回もしくは繰り返し処理を行った。好気条件においてはマンガン酸化物によるCr(III)のCr(VI)への酸化が認められた。この際、Mn(IV)がMn(II)に一旦還元されるものの真菌の活性のためMn(II)の再酸化により溶液中ではマンガンは検出されなかった。一方、嫌気条件においてはCr(III)の酸化は反応の初期段階で停止し、Mn(II)の再酸化が起こらないため還元されたマンガンが溶液中で検出された。
Wang, H.*; 大津 秀暁*; 千賀 信幸*; 川瀬 頌一郎*; 武内 聡*; 炭竃 聡之*; 小山 俊平*; 櫻井 博儀*; 渡辺 幸信*; 中山 梓介; et al.
Communications Physics (Internet), 2(1), p.78_1 - 78_6, 2019/07
被引用回数:8 パーセンタイル:56.2(Physics, Multidisciplinary)陽子(あるいは中性子)過剰核の効率的な生成経路を探索することは、原子核反応研究の主な動機のひとつである。本研究では、Pdに対する核子当たり50MeVの陽子および重陽子入射による残留核生成断面積を逆運動学法によって測定した。その結果、重陽子入射ではAgやPd同位体の生成断面積が大きくなることを実験的に示した。また、理論計算による解析から、この生成断面積の増大は重陽子の不完全融合反応に起因することを示した。これらの結果は、陽子過剰核の生成において重陽子のような弱束縛核の利用が有効であることを示すものである。
鈴木 賢治*; 菖蒲 敬久; 城 鮎美*
材料, 68(4), p.312 - 317, 2019/04
溶接等の熱加工後の材料においては粗大粒を有する場合が多い。これらの加工後の残留応力を把握することは構造物の健全性の観点から非常に重要視されている。本研究では、粗大粒を持つ材料のX線応力測定法として、2次元検出器と高エネルギー放射光を組み合わせた二重露光法を提案し、その実用性を確認した。アルミニウム合金の塑性曲げ試験片及び圧痕試験片の残留応力を計測した結果、有限要素解析による残留応力分布とよく一致していることから、本測定手法の有効性が明らかとなった。
鈴木 賢治*; 菖蒲 敬久
E-Journal of Advanced Maintenance (Internet), 10(4), p.9 - 17, 2019/02
弾性異方性をもつ材料中では、塑性変形が発生した際に結晶間に応力差が生じており、これが材料破壊に深くかかわっていることが知られている。本研究では、高エネルギー放射光回折法を用いて、塑性変形させた材料中の荷重方向の残留応力を結晶方位ごとに調べた。その結果、残留応力はX線的弾性定数(回折面ごとに求められるヤング率)が高い指数では引張残留応力、低い指数では圧縮残留応力が発生していることがわかった。この結果は、材料強度を向上させる際、集合組織のように結晶方位を制御する技術に役立つと考えている。
Bae, S.*; Jee, H.*; 兼松 学*; 城 鮎美*; 町田 晃彦*; 綿貫 徹*; 菖蒲 敬久; 鈴木 裕士
Journal of the American Ceramic Society, 101(1), p.408 - 418, 2018/01
被引用回数:17 パーセンタイル:64.48(Materials Science, Ceramics)ケイ酸カルシウム水和物(CSH)に関する原子レベルの構造や変形機構には不明な点が多い。本研究では、X線散乱法に基づく原子対相関関数(PDF)により、ケイ酸三カルシウム(CS)ペースト中に存在するCSH相のナノ構造変形挙動を評価した。単軸圧縮負荷を受けるCSペーストの変形を、ひずみゲージ,ブラッグピークシフト, PDFから求められるマクロからミクロな変形より評価した。PDF解析により、0-20の範囲ではCSH相の影響が支配的であること、その一方で、20を超える範囲では、他の結晶相の影響が支配的であることが明らかとなった。CSHの変形に支配的である20以下の範囲では、塑性変形を示すステージI(0-10MPa)と、弾性変形を示すステージIIの2つの変形過程に分けられることが分かった。その一方で、20以上の範囲では、水酸化カルシウムに似た変形を示した。10MPa以下では、層間水やゲル水の移動に伴い、CSHの高密度化を生じたと考えられるが、除荷後には、その移動した水がCSH中に戻ることにより、変形が回復している可能性がある。
生島 一樹*; 柴原 正和*; 西川 聡*; 古川 敬*; 秋田 貢一; 鈴木 裕士; 諸岡 聡
E-Journal of Advanced Maintenance (Internet), 9(3), p.NT87_1 - NT87_5, 2017/11
In this work, an analysis system that can analyze the modification of the residual stress distribution by peening is proposed based on IEFEM. In the proposed analysis system, IEFEM is extended to consider the dynamic effect to analyze the dynamic phenomenon with an impulsive load. The impulsive load due to the collision of shots is modeled as an equivalent load model. The equivalent load model is integrated with IEFEM considering the dynamic effect to calculate spatially and temporally random load in dynamic analyses. Using the proposed analysis system, the residual stress distribution modification by shot peening in a multi-pass welded pipe joint is predicted. The residual stress distributions obtained by the analysis are compared with those measured by X-ray diffraction (XRD), and the effect of the number of shot collisions on the change in residual stress distribution is discussed.
秋田 貢一; 柴原 正和*; 生島 一樹*; 西川 聡*; 古川 敬*; 鈴木 裕士; Harjo, S.; 川崎 卓郎; Vladimir, L.*
溶接学会論文集(インターネット), 35(2), p.112s - 116s, 2017/06
Residual stresses near the weld metal of the joints before and after a thermal cycle were measured using a reactor based neutron diffraction technique in room temperature. In-situ residual stress measurements were performed on the plate type sample using a pulsed neutron diffraction technique under thermal cycles. Residual stress behaviors of the samples were examined also by the idealized explicit FEM (IEFEM), which agreed well with the experimental results of the residual stress behaviors during thermal cycles. Thermal stresses were induced near the weld metal by the difference of the linear expansion coefficients of the dissimilar base metals. Since the thermal stress exceeded the yield stress of the material during the first heating process, the residual stresses near the weld metal were redistributed and a part of the residual stress was relaxed.
生島 一樹*; 木谷 悠二*; 柴原 正和*; 西川 聡*; 古川 敬*; 秋田 貢一; 鈴木 裕士; 諸岡 聡
溶接学会論文集(インターネット), 35(2), p.75s - 79s, 2017/06
In this research, to investigate the effect of shot peening on operation, an analysis method to predict the behavior of stress distribution on shot peening was proposed. In the proposed system, the load distribution on the collision of shots was modeled, and it was integrated with the dynamic analysis method based on the Idealized explicit FEM (IEFEM). The thermal elastic plastic analysis method using IEFEM was applied to the analysis of residual stress distribution of multi-pass welded pipe joint. The computed residual stress distribution was compared with the measured residual stress distribution using X-ray diffraction (XRD). As a result, it was shown that the both welding residual stress distribution agree well with each other. Considering the computed welding residual stress distribution, the modification of stress distribution due to shot peening was predicted by the proposed analysis system.
小島 真由美*; 城 鮎美*; 鈴木 裕士; 井上 純哉*; 菖蒲 敬久; 徐 平光; 秋田 貢一; 南部 将一*; 小関 敏彦*
材料, 66(6), p.420 - 426, 2017/06
The strain distribution in a multilayered steel composite, which consists of martensite and austenite layers, was evaluated by energy dispersive X-ray diffraction to investigate the homogeneity of deformation in the martensite layer under uniaxial loading. A dog-bone shape specimen with a martensite layer with 0.2 mm in a thickness, sandwiching by austenite layers with 0.4 mm in thickness, was utilized in this study. A change in strains as a function of tensile loading was measured at the center of the martensite layer as well as near the interface between the martensite and austenite layers. Furthermore, the residual strain distributions were measured in the martensite layer of the unloaded specimens after different applied strains. As a result, slight inhomogeneous deformation was found at the beginning of the plastic deformation in the martensite layer although no local deformation was recognized even near the interface between austenite and martensite layers. After further deformation, mismatch of plastic deformation between austenite and martensite layers was reduced, and the martensite layer deformed homogeneously. Therefore, an unstable interface phenomenon might not be caused by the intrinsic factors with a mesoscopic scale discussed in this experiment.
生島 一樹*; 柴原 正和*; 秋田 貢一; 鈴木 裕士; 諸岡 聡; 西川 聡*; 古川 敬*
Welding in the World, 61(3), p.517 - 527, 2017/05
本研究では、先ず、ショットピーニングプロセスにおける残留応力の挙動を予測するための解析手法を提案した。この手法ではショットの衝突時の荷重分布をモデル化し、さらに、理想化陽解法FEM解析手法(IEFEM)に基づく動的解析法と組み合わせた。提案した解析システムの解析精度は、ショット一発が衝突した際の応力分布をABAQUSによる解析結果と比較することで確認した。IEFEMを用いて熱弾塑性解析を実施し、配管のマルチパス溶接における溶接残留応力の解析を実施し、解析結果をX線回折による残留応力測定結果と比較し、両者がよく一致することを確認した。次いで、ショットピーニングによる溶接残留応力の変化を提案システムによって解析した。その結果、多量のショットを衝突した場合の残留応力は、解析と実験とでよく一致した。
高橋 悟*; 野田 祥希*; 松田 朝陽*; 川端 邦明; 鈴木 剛*; 武村 史朗*; 小笠原 敬*; 金子 俊一*
Journal of Signal Processing, 21(1), p.15 - 24, 2017/01
地球環境の変動に伴う海洋生態系の変化を中長期的に渡り自動観測を行う装置の開発は重要である。特に、多様な海洋生態系に対して重要な役割を担うサンゴ礁は地球環境変動の影響を多大に受けていることが認知されている。本論文では、方向符号の情報量を評価する豊富度に基づき海中ランドマークの生成方法と、方向符号照合法に複数枚テンプレートマッチングかつ粒子フィルタによる海中ランドマークの位置推定を施すことにより、海中ランドマークの位置決定を行う手法を提案する。そして、海中ランドマークの時系列的な位置計測を実施した。