Rabi-oscillation spectroscopy of the hyperfine structure of muonium atoms

Nishimura, Shoichiro*; Torii, Hiroyuki*; Fukao, Yoshinori*; Ito, Takashi; Iwasaki, Masahiko*; Kanda, Sotaro*; Kawagoe, Kiyotomo*; Kawall, D.*; Kawamura, Naritoshi*; Kurosawa, Noriyuki*; et al.

Physical Review A, 104(2), p.L020801_1 - L020801_6, 2021/08

https://doi.org/10.1103/PhysRevA.104.L020801

Study on optical properties of metallic sodium by vacuum ultra violet in UVSOR

Kawaguchi, Munemichi; Saito, Junichi; Daido, Hiroyuki*; Suemoto, Toru*

UVSOR-46, P. 89, 2019/08

https://www.uvsor.ims.ac.jp/eng/activity/2018/page_02.html

To elucidate theoretically the transparent metallic sodium in the vacuum ultraviolet spectral range, the aim of this research is to obtain the accurate spectrum using UVSOR. The sodium sample maintained metallic luster by designing the special cells to prevent from oxidizing. The results of UVSOR measurement showed the possibility to occur the intransparent layer for vacuum ultraviolet light on the MgF windows. In the near future, we will improve the sodium sample to solve the problems and conduct the measurement again

Dry cleaning process test for fuel assembly of fast reactor plant system, 2; Laboratory scale test for fuel assembly and evaluation of the amount of residual sodium

Ide, Akihiro*; Kudo, Hideyuki*; Inuzuka, Taisuke*; Hara, Masahide*; Kato, Atsushi; Ishikawa, Nobuyuki; Otaka, Masahiko; Nagai, Keiichi; Saito, Junichi; Ara, Kuniaki

Proceedings of 2019 International Congress on Advances in Nuclear Power Plants (ICAPP 2019) (Internet), 10 Pages, 2019/05

A next generation SFR in Japan has adopted an advanced dry cleaning system which consists of the following process of argon gas blowing to reduce the amount of metallic sodium, moist argon gas blowing to deactivate the residual sodium, and direct storage in the SFP without using storage containers. This three-step process increases economic competitiveness and reduces waste products. In this Research and Development work, the amount of residual sodium and performance of the dry cleaning process were investigated. This paper describes experimental and analytical work for all parts of a fuel assembly except for a fuel pin bundle.

New precise measurement of muonium hyperfine structure interval at J-PARC

Ueno, Yasuhiro*; Aoki, Masaharu*; Fukao, Yoshinori*; Higashi, Yoshitaka*; Higuchi, Takashi*; Iinuma, Hiromi*; Ikedo, Yutaka*; Ishida, Katsuhiko*; Ito, Takashi; Iwasaki, Masahiko*; et al.

Hyperfine Interactions, 238(1), p.14_1 - 14_6, 2017/11

https://doi.org/10.1007/s10751-016-1381-7

Annual report of Nuclear Emergency Assistance and Training Center (April 1, 2013 - March 31, 2014)

Sato, Takeshi; Muto, Shigeo; Akiyama, Kiyomitsu; Aoki, Kazufumi; Okamoto, Akiko; Kawakami, Takeshi; Kume, Nobuhide; Nakanishi, Chika; Koie, Masahiro; Kawamata, Hiroyuki; et al.

JAEA-Review 2014-048, 69 Pages, 2015/02

JAEA-Review-2014-048.pdf:13.91MB

JAEA was assigned as a designated public institution under the Disaster Countermeasures Basic Act and under the Armed Attack Situations Response Act. Based on these Acts, the JAEA has the responsibility of providing technical support to the national government and/or local governments in case of disaster responses or response in the event of a military attack, etc. In order to fulfill the tasks, the JAEA has established the Emergency Action Plan and the Civil Protection Action Plan. In case of a nuclear emergency, NEAT dispatches specialists of JAEA, supplies the national government and local governments with emergency equipment and materials, and gives technical advice and information. In normal time, NEAT provides various exercises and training courses concerning nuclear disaster prevention to those personnel taking an active part in emergency response institutions of the national and local governments, police, fire fighters, self-defense forces, etc. in addition to the JAEA itself. The NEAT also researches nuclear disaster preparedness and response, and cooperates with international organizations. In the FY2013, the NEAT accomplished the following tasks: (1) Technical support activities as a designated public institution in cooperation with the national and local governments, etc. (2) Human resource development, exercise and training of nuclear emergency response personnel for the national and local governments, etc. (3) Researches on nuclear disaster preparedness and response, and sending useful information (4) International contributions to Asian countries on nuclear disaster preparedness and response in collaboration with the international organizations

Characterization and storage of radioactive zeolite waste

Yamagishi, Isao; Nagaishi, Ryuji; Kato, Chiaki; Morita, Keisuke; Terada, Atsuhiko; Kamiji, Yu; Hino, Ryutaro; Sato, Hiroyuki; Nishihara, Kenji; Tsubata, Yasuhiro; et al.

Journal of Nuclear Science and Technology, 51(7-8), p.1044 - 1053, 2014/07

https://doi.org/10.1080/00223131.2014.924446

For safe storage of zeolite wastes generated by treatment of radioactive saline water at the Fukushima Daiichi Nuclear Power Station, properties of the Herschelite adsorbent were studied and its adsorption vessel was evaluated for hydrogen production and corrosion. Hydrogen production depends on its water level and dissolved species because hydrogen is oxidized by radicals in water. It is possible to evaluate hydrogen production rate in Herschelite submerged in seawater or pure water by taking into account of the depth effect of the water. The reference vessel of decay heat 504 W with or without residual pure water was evaluated for the hydrogen concentration by thermal hydraulic analysis using obtained fundamental properties. Maximum hydrogen concentration was below the lower explosive limit (4 %). The steady-state corrosion potential of a stainless steel 316L increased with absorbed dose rate but its increase was repressed by the presence of Herschelite. At 750 Gy/h and 60C which were values evaluated at the bottom of the vessel of 504 W, the localized corrosion of SUS316L contacted with Herschelite would not immediately occur under 20,000 ppm of Cl concentration.

Spin pumping efficiency from half metallic CoMnSi

Chudo, Hiroyuki; Ando, Kazuya*; Saito, Kesami*; Okayasu, Satoru; Haruki, Rie; Sakuraba, Yuya*; Yasuoka, Hiroshi; Takanashi, Koki; Saito, Eiji

Journal of Applied Physics, 109(7), p.073915_1 - 073915_4, 2011/04

https://doi.org/10.1063/1.3556433

We present spin pumping using a Heusler alloy CoMnSi/Pt bilayer film. A spin current is produced by a ferromagnetic resonance (FMR) technique. The pure spin current injected into the Pt layer from the CoMnSi layer is detected by the inverse spin-Hall effect (ISHE), which converts the spin current into an electric current. We estimated a damping constant of the CoMnSi/Pt bilayer film from an angular dependence of FMR spectra. Using the damping constant efficiency of spin pumping from the CoMnSi layer is evaluated. We found that a mixing conductance at the CoMnSi/Pt interface is comparable to that at a permalloy/Pt interface.

Basic vacuum test of 500-kV photocathode DC gun components at KEK

Yamamoto, Masahiro*; Uchiyama, Takashi*; Miyajima, Tsukasa*; Honda, Yosuke*; Sato, Kotaro*; Matsuba, Shunya*; Saito, Yoshio*; Kobayashi, Masanori*; Kurisu, Hiriki*; Hajima, Ryoichi; et al.

Proceedings of 7th Annual Meeting of Particle Accelerator Society of Japan (DVD-ROM), p.717 - 720, 2010/08

http://www.pasj.jp/web_publish/pasj7/proceedings/P_4PM/P_EH_4PM/WEPS124.pdf

A 500-kV photocathode DC electron gun which can supply the beam of a low emittance and a high average current has been developed in collaboration with KEK, JAEA, Hiroshima Univ., Nagoya Univ. and Yamaguchi Univ. The vacuum of the gun chamber has to be lower Extreme High Vacuum for maintain cathode-life time. A titanium chamber and new material of ceramic were employed to reduce outgassing rate. The result of outgassing rate of the gun chamber is described in this report.

Design of a 500kV electron gun for ERL light source at KEK

Yamamoto, Masahiro*; Honda, Yosuke*; Miyajima, Tsukasa*; Uchiyama, Takashi*; Kobayashi, Masanori*; Muto, Toshiya*; Matsuba, Shunya*; Sakanaka, Shogo*; Sato, Kotaro*; Saito, Yoshio*; et al.

Proceedings of 6th Annual Meeting of Particle Accelerator Society of Japan (CD-ROM), p.860 - 862, 2009/08

A newly 500 kV electron gun (2nd - 500 kV gun) for an ERL light source is designed at KEK. A new concept and state of-the-art technologies of vacuum system, ceramic insulators, high voltage power supply, photocathode and preparation system will be employed. The details are described in this report.

Sputter etching of Si substrate to synthesize highly oriented -FeSi films

Igarashi, Shinichi; Katsumata, Toshinobu; Haraguchi, Masaharu; Saito, Takeru; Yamaguchi, Kenji; Yamamoto, Hiroyuki; Hojo, Kiichi

Transactions of the Materials Research Society of Japan, 28(4), p.1153 - 1156, 2003/12

We have evaluated the crystal structure of the -FeSi films formed with various sputter etching of Si substrate. Ne sputter etching of Si (100) substrate was performed with ion energies of 1, 3, and 10 keV. After each etching, the substrate was annealed at a temperature of 1073 K for 30 min. The -FeSi films of 100 nm in thickness were formed at 973 K with the amount of deposited Fe, 30 nm. X-ray diffraction revealed that these films have polycrystalline -FeSi structure but strong preferential orientation aligned as -FeSi (100) // Si (100). Furthermore, the oriented structure of the film was improved by lowering the incident energy of Ne.