Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
田口 美岐*; 宮田 登*; 宮崎 司*; 青木 裕之; Ozawa, Satoru*; 長谷川 龍一 *; 盛満 裕真*; 川口 大輔*; 山本 悟*; 田中 敬二*
Polymer Journal, 7 Pages, 2025/03
Polyrotaxane (PR) exhibits unique mechanical properties due to the ability of its cyclic molecules to move or slide along the axial chain. Thus, to design advanced polymer-based composite materials and organic devices, it is crucial to better understand the aggregation states at the surface and substrate interface in polymer films containing PR. Here, we report the depth profile of PR along the direction normal to the interface when it is mixed with polystyrene (PS). Neutron reflectivity and X-ray photoelectron spectroscopy revealed that PS and PR segregated at the surface and substrate interface, respectively, and that the extent of segregation depended on the length of PS. The surface enrichment of PS is driven by both energy and entropy, whereas the enrichment of PR at the substrate interface is energy driven.
山本 勝宏*; 今井 達也*; 河合 純希*; 伊藤 恵利*; 宮崎 司*; 宮田 登*; 山田 悟史*; 瀬戸 秀紀*; 青木 裕之
ACS Applied Materials & Interfaces, 16(48), p.66782 - 66791, 2024/11
被引用回数:0 パーセンタイル:0.00(Nanoscience & Nanotechnology)In this study, a silicon-based copolymer, poly(tris(trimethylsiloxy)-3-methacryloxypropylsilane)-co-poly(N,N-dimethyl acrylamide), thin film was subjected to plasma surface treatment to make its surface hydrophilic (biocompatible). Neutron reflectivity (NR) measurement of the plasma-treated thin film showed a decrease in the film thickness (etching width: similar to 20 nm) and an increase in the scattering length density (SLD) near the surface (similar to 15 nm). The region with a considerably high SLD adsorbed water (DO) from its saturated vapor, indicating its superior surface hydrophilicity. Nevertheless of the hydrophilicity, the swelling of the thin film was suppressed. Hard X-ray photoelectron spectroscopy (HAXPES) performed at various takeoff angles revealed that the thin-film surface (similar to 20 nm depth) underwent extensive oxidation. NR and HAXPES analysis quantitatively yielded the depth profiling of elemental compositions in a few tens of nm scale. Si oxidation and hydrogen elimination (probably CH
groups) in the vicinity of the surface region increased the SLD and decreased the hydrophobicity. A combination of Soft X-ray photoelectron spectroscopy and NR measurements revealed the surface chemical composition and mass density. It was considered that the surface near the film was chemically composed close to SiO
, forming a gel-like (three-dimensional network) structure that is hydrophilic and suppresses swelling due to moisture, indicating it can be expected to maintain stable hydrophilicity on the film surface.
宮崎 司*; 宮田 登*; 有馬 寛*; 下北 啓輔*; 山本 勝宏*; 竹中 幹人*; 中西 洋平*; 柴田 基樹*; 青木 裕之; 山田 悟史*; et al.
Colloids and Surfaces A; Physicochemical and Engineering Aspects, 701, p.134928_1 - 134928_8, 2024/11
被引用回数:0 パーセンタイル:0.00(Chemistry, Physical)Isotactic polypropylene (PP) thin films deposited on Si substrates were subjected to neutron reflectivity (NR) measurements under various humidity conditions to evaluate the isothermal adsorption of water accumulated between the PP layer and Si substrate, with focus on the temperature-dependence of the adsorption isotherm. The adsorption of accumulated water followed a single type II isotherm according to the Brunauer-Emmett-Teller (BET) classification, regardless of temperature. This can be attributed to the weak interactions between the PP layer and Si substrate, and between the PP layer and water molecules. Hydrophobic PP does not significantly interact with water molecules and the hydrophilic Si surface. Therefore, the interfacial water molecules are simply adsorbed on the native oxide layer on Si via simple interaction between the water molecules and the silicon oxide surface without being affected by the PP layer. Consequently, the adsorption isotherm of the accumulated water follows the single type II adsorption isotherm regardless of temperature, similar to the adsorption isotherm of water simply adsorbed on exposed silica surfaces. These weak interactions of the PP layer with the Si surface and water molecules also lead to fast diffusion kinetics for the accumulated water along the interface.
下北 啓輔*; 山本 勝宏*; 宮田 登*; 柴田 基樹*; 中西 洋平*; 荒川 勝利*; 竹中 幹人*; 木田 拓充*; 徳満 勝久*; 田中 亮*; et al.
Langmuir, 40(30), p.15758 - 15766, 2024/07
被引用回数:0 パーセンタイル:0.00(Chemistry, Multidisciplinary)To investigate the structure of the interface between polyethylene films and substrates, the neutron reflectivity (NR) of deuterated polyethylene (dPE) thin films deposited on Si substrates was measured, demonstrating water accumulation at the interface, even under ambient conditions. After leaching the thermally annealed dPE films in hot p-xylene, NR measurements were conducted on the layers remaining on the substrate, clearly revealing that the adsorption layer of dPE grew during annealing and consisted of two layers, an inner adsorption layer and an outer adsorption layer, as previously proposed for amorphous polymers. The inner adsorption layer was approximately 3.7 nm thick with a density comparable to that of the bulk. The outer adsorption layer was several nanometers thick and appeared to grow insufficiently on top of the inner adsorption layer under the annealing conditions examined in this study. This study clarifying the growth of the adsorption layer of polyethylene at the interface with an inorganic substrate is useful for improving the performance of polymer/inorganic filler nanocomposites due to the wide utility of crystalline polyolefins as polymer matrix materials in nanocomposites.
Kawano, Masayuki*; 盛満 裕真*; Liu, Y.*; 宮田 登*; 宮崎 司*; 青木 裕之; 川口 大輔*; 山本 悟*; 田中 敬二*
Macromolecules, 57(14), p.6625 - 6633, 2024/07
被引用回数:0 パーセンタイル:0.00(Polymer Science)A better understanding of the dynamic behavior of polymer chains on solid surfaces is indispensable for the design and construction of high-performance polymer composites. We herein visualized the in-plane movement of isolated poly(methyl methacrylate) (PMMA) and poly(tert-butyl methacrylate) (PtBMA) single chains on hydrophilic silicon wafers under ambient conditions by atomic force microscopy. Isolated PMMA chains adsorbed to the substrate, whereas PtBMA chains diffused, the degree of which was dependent on the humidity. Neutron reflectivity revealed the formation of a layer of condensed water on the substrate. All-atomistic molecular dynamics simulations implied that the diffusivity difference of the two polymers was based on the submerged depth in which a part of a chain existed. That is, the interaction of a polymer with the surface of the hydrophilic substrate primarily governs its lateral movement, or adsorption behavior, facilitated by the presence of water.
渡邉 和彦*; 仁木 和昭*; 高橋 博樹; 山本 昇*; 吉本 政弘; 福田 真平*
Proceedings of 20th Annual Meeting of Particle Accelerator Society of Japan (インターネット), p.844 - 847, 2023/11
J-PARC加速器の人員保護システム(PPS)はデータ収集用PC群と情報表示PC群で構成されるPPS Data Systemと加速器施設等のPLC群とをPPSのネットワークにより接続することでデータ収集・表示を行っている。PPS Data SystemではSCADAソフトウェアを使用してきたが、信号点数の制限やOS依存等の問題があることから、別ソフトウェアでの構築が必要となった。そこでJ-PARC制御システムで実績があるEPICSを採用して新システムを構築することとした。一方、PPSは人員の安全を担保するシステムであり長期間停止することができない。また、最も重要な安全システムであることから高い信頼性及び安定性を保つ必要があり、一度に新システムへ移行することは危険である。そこで既存システムを機能毎に分割し、既存ステムの稼働と並行して部分的に新システムを稼働させていく方針とした。これによりPPSの機能を損なうことなく動作検証や不具合修正を長期間実施でき、新システムの信頼性及び安定性を確保することが可能となる。本発表では新システムの概要と移行プロセス及び進捗状況について報告する。
下北 啓輔*; 山本 勝宏*; 宮田 登*; 中西 洋平*; 柴田 基樹*; 竹中 幹人*; 山田 悟史*; 瀬戸 秀樹*; 青木 裕之; 宮崎 司*
Soft Matter, 19(11), p.2082 - 2089, 2023/03
被引用回数:3 パーセンタイル:56.29(Chemistry, Physical)In the case of poly(methyl methacrylate) (PMMA) thin films on a Si substrate, thermal annealing induces the formation of a layer of PMMA chains tightly adsorbed near the substrate interface, and the strongly adsorbed PMMA remains on the substrate, even after washing with toluene (hereinafter called adsorbed sample). Neutron reflectometry revealed that the concerned structure consists of three layers: an inner layer (tightly bound on the substrate), a middle layer (bulk-like), and an outer layer (surface) in the adsorbed sample. When an adsorbed sample was exposed to toluene vapor, it became clear that, between the solid adsorption layer (which does not swell) and bulk-like swollen layer, there was a "buffer layer" that could sorb more toluene molecules than the bulk-like layer. This buffer layer was found not only in the adsorbed sample but also in the standard spin-cast PMMA thin films on the substrate. When the polymer chains were firmly adsorbed and immobilized on the Si substrate, the freedom of the possible structure right next to the tightly bound layer was reduced, which restricted the relaxation of the conformation of the polymer chain strongly. The "buffer layer" was manifested by the sorption of toluene with different scattering length density contrasts.
下北 啓輔*; 山本 勝宏*; 宮田 登*; 有馬 寛*; 中西 洋平*; 竹中 幹人*; 柴田 基樹*; 山田 悟史*; 瀬戸 秀樹*; 青木 裕之; et al.
Langmuir, 38(41), p.12457 - 12465, 2022/10
被引用回数:2 パーセンタイル:14.75(Chemistry, Multidisciplinary)We measured the neutron reflectivity (NR) of isotactic polypropylene (PP) thin films deposited on Si substrates modified by hexamethyldisilazane (HMDS) at the saturated vapor pressure of deuterated water at 25C and 60
C/85% RH to investigate the effect of HMDS on the interfacial water accumulation in PP-based polymer/inorganic filler nanocomposites and metal/resin bonding materials. We found that the amount of water accumulated at the PP/Si interface decreased with increasing immersion time of the Si substrate in a solution of HMDS in hexane prior to PP film deposition. During the immersion of the Si substrate, the HMDS molecules were deposited on the Si substrate as a monolayer without aggregation. Furthermore, the coverage of the HMDS monolayer on the Si substrate increased with increasing immersion time. At 60
C and 85% RH, only a slight amount of interfacial water was detected after HMDS treatment for 1200 min. As a result, the maximum concentration of interfacial water was reduced to 0.1 from 0.3, where the latter corresponds to the PP film deposited on the untreated substrate.
Yamaguchi, Ko*; 川口 大輔*; 宮田 登*; 宮崎 司*; 青木 裕之; 山本 悟*; 田中 敬二*
Physical Chemistry Chemical Physics, 24(36), p.21578 - 21582, 2022/09
被引用回数:12 パーセンタイル:80.92(Chemistry, Physical)A better understanding of the chemical reaction between epoxy and amine compounds at a solid interface is crucial for the design and fabrication of materials with appropriate adhesive strength. Here, we examined the curing reaction kinetics of epoxy phenol novolac and 4,4'-diaminodiphenyl sulfone at the outermost interface using sum-frequency generation spectroscopy, and X-ray and neutron reflectivity in conjunction with a full atomistic molecular dynamics simulation. The reaction rate constant was much larger at the quartz interface than in the bulk. While the apparent activation energy at the quartz interface obtained from an Arrhenius plot was almost identical to the bulk value, the frequency factor at the quartz interface was greater than that in the bulk. These results could be explained in terms of the densification and orientation of reactants at the interface, facilitating the encounter of the reactants present.
宮崎 司*; 下北 啓輔*; 山本 勝宏*; 青木 裕之; 山田 悟史*; 宮田 登*
Langmuir, 36(49), p.15181 - 15188, 2020/12
被引用回数:8 パーセンタイル:33.26(Chemistry, Multidisciplinary)We investigated the polymer chain dynamics in a 2-3 nm thick poly(vinyl acetate) (PVAc) adsorption layer on a Si substrate with a native oxide layer via neutron reflectometry combined with toluene vapor-induced swelling. We can investigate the polymer chain dynamics difference in the film thickness direction by the difference in the degree of swelling of the polymer layers detected by neutron reflectometry. The mobility of the polymer chains depends on the distance from the substrate. The results elucidated that the interfacial layer with a thickness of approximately 1 nm did not swell at all with toluene vapor, which is a solvent for PVAc. Meanwhile, the surface layer excessively swells with toluene vapor compared to the bulk. This indicates that the polymer chain within the interfacial region is immobilized by the substrate through hydrogen-bonding interaction, but in the surface region, the surface effect overcomes this interfacial interaction. We concluded that the polymer chains in the adsorption layer are either strongly constrained to the substrate, owing to hydrogen bonding, or more mobile than the bulk, owing to the surface effect.
宮崎 司*; 宮田 登*; 吉田 鉄生*; 有馬 寛*; 津村 佳弘*; 鳥飼 直也*; 青木 裕之; 山本 勝宏*; 金谷 利治*; 川口 大輔*; et al.
Langmuir, 36(13), p.3415 - 3424, 2020/04
被引用回数:17 パーセンタイル:59.50(Chemistry, Multidisciplinary)We investigated in detail the structures in the poly(vinyl alcohol) (PVA) adsorption layers on a Si substrate, which remained on the substrate after immersing the relatively thick 30 - 50 nm films in hot water, by neutron reflectometry under humid conditions. For the PVA with a degree of saponification exceeding 98 mol %, the adsorption layer exhibits a three-layered structure in the thickness direction. The bottom layer is considered to be the so-called inner adsorption layer that is not fully swollen with water vapor. This may be because the polymer chains in the inner adsorption layer are strongly constrained onto the substrate, which inhibits water vapor penetration. The polymer chains in this layer have many contact points to the substrate via the hydrogen bonding between the hydroxyl groups in the polymer chain and the silanol groups on the surface of the Si substrate and consequently exhibit extremely slow dynamics. Therefore, it is inferred that the bottom layer is fully amorphous. Furthermore, we consider the middle layer to be somewhat amorphous because parts of the molecular chains are pinned below the interface between the middle and bottom layers. The molecular chains in the top layer become more mobile and ordered, owing to the large distance from the strongly constrained bottom layer; therefore, they exhibit a much lower degree of swelling compared to the middle amorphous layer. Meanwhile, for the PVA with a much lower degree of saponification, the adsorption layer structure consists of the two-layers. The bottom layer forms the inner adsorption layer that moderately swells with water vapor because the polymer chains have few contact points to the substrate. The molecular chains in the middle layer, therefore, are somewhat crystallizable because of this weak constraint.
宮崎 司*; 宮田 登*; 浅田 光則*; 津村 佳弘*; 鳥飼 直也*; 青木 裕之; 山本 勝宏*; 金谷 利治*; 川口 大輔*; 田中 敬二*
Langmuir, 35(34), p.11099 - 11107, 2019/08
被引用回数:25 パーセンタイル:67.04(Chemistry, Multidisciplinary)We investigated the swelling behaviors of poly(vinyl alcohol) (PVA) films deposited on Si wafers with water vapor, which is a good solvent for PVA for elucidating structural and dynamical heterogeneities in the film thickness direction. Using deuterated water vapor, structural and dynamical differences in the thickness direction can be detected easily as different degrees of swelling in the thickness direction by neutron reflectivity. Consequently, the PVA film with a degree of saponification exceeding 98 mol % exhibits a three-layered structure in the thickness direction. It is considered that an adsorption layer consisting of molecular chains that are strongly adsorbed onto the solid substrate is formed at the interface with the substrate, which is not swollen with water vapor compared with the bulk-like layer above it. The adsorption layer is considered to exhibit significantly slower dynamics than the bulk. Furthermore, a surface layer that swells excessively compared with the underneath bulk-like layer is found. This excess swelling of the surface layer may be related to a higher mobility of the molecular chains or lower crystallinity at the surface region compared to the underneath bulk-like layer. Meanwhile, for the PVA film with a much lower degree of saponification, a thin layer with a slightly lower degree of swelling than the bulk-like layer above it can be detected at the interface between the film and substrate only under a high humidity condition. This layer is considered to be the adsorption layer composed of molecular chains loosely adsorbed onto the Si substrate.
菊澤 信宏; 仁木 和昭*; 山本 昇*; 林 直樹; 足立 昌俊*; 渡邉 和彦*
Proceedings of 16th Annual Meeting of Particle Accelerator Society of Japan (インターネット), p.877 - 880, 2019/07
J-PARCのインターロックシステムは、人の安全のための人的保護システム(Personnel Protection System: PPS)および機器を保護するための機器保護システム(Machine Protection System: MPS)に大別される。J-PARCのPPSは2006年のLinacでの部分運用から始まり2009年のハドロン実験施設およびニュートリノ実験施設の稼働で完成した。その後の10年でビデオ監視システムの更新や新しいインターロックの新設などの改善や改良が行われてきた。本報告ではこれらを含めた最近の運用について述べるとともに、信頼性を維持・向上させるために実施している検査やメンテナンスについての現状を報告する。
長谷川 和男; 金正 倫計; 小栗 英知; 山本 風海; 林 直樹; 山崎 良雄; 内藤 富士雄*; 吉井 正人*; 外山 毅*; 山本 昇*; et al.
Proceedings of 16th Annual Meeting of Particle Accelerator Society of Japan (インターネット), p.1235 - 1239, 2019/07
J-PARCでは2018年の夏季メンテナンス終了後、3GeVシンクロトロン(RCS)からビームを供給する物質・生命科学実験施設(MLF)での利用運転を10月下旬から再開した。出力は夏前の500kWと同じであるが、リニアックのピークビーム電流値を、夏前の40mAから定格の50mAに上げた。一方、スーパーカミオカンデの改修やハドロン実験施設の保守や整備などもあり、30GeVのメインリング(MR)のビーム運転は休止したが、利用運転は2月中旬からハドロン実験施設向けに51kWで再開した。しかし3月18日、MRへの入射ビームラインでの偏向電磁石1台に不具合が発生し、仮復旧で4月5日に利用運転を再開したが、再度不具合が発生し4月24日に夏前の利用運転を終了した。2018年度の稼働率は、リニアック, RCSともに安定でMLF向けは94%、ニュートリノとハドロン実験施設向けは86%、74%であった。ここでは、こうした1年間の運転経験を報告する。
長谷川 和男; 金正 倫計; 小栗 英知; 山本 風海; 林 直樹; 山崎 良雄; 内藤 富士雄*; 吉井 正人*; 山本 昇*; 小関 忠*
Proceedings of 15th Annual Meeting of Particle Accelerator Society of Japan (インターネット), p.1317 - 1321, 2018/08
J-PARCでは2017年の夏季メンテナンス終了後、10月下旬から利用運転を再開した。3GeVシンクロトロンからビームを供給する物質・生命科学実験施設(MLF)では、予備の標的を使ってきたため出力は150-200kWであったが、夏季メンテナンス中に新しい設計で製作した標的に交換した。この結果、11月に300kW、1月から400kW、4月下旬から500kWと徐々に利用運転の出力を向上した。また、2018年の7月に1MWの1時間の連続試験に成功した。30GeVのメインリングでは、ニュートリノ実験施設(NU)への供給を10月下旬から開始し、440kWから出力を上げ12月には470kWで終了した。2018年1月から2月はハドロン実験施設(HD)に供給した。繰り返しを5.52から5.20秒に速め、調整を進めた結果、出力は44kWから50kWに向上した。3月からNUへの供給を再開し、調整の結果490kWを安定に供給できるようになった。稼働率は、2017年度はリニアック、RCSともに安定で、MLF向けは93%であった。MRでは、NU向けは比較的安定で89%、HD向けは66%(2017年4月に発生したESS不具合の影響が大きい)であった。
長谷川 和男; 林 直樹; 小栗 英知; 山本 風海; 金正 倫計; 山崎 良雄; 内藤 富士雄; 小関 忠; 山本 昇; 吉井 正人
Proceedings of 9th International Particle Accelerator Conference (IPAC '18) (Internet), p.1038 - 1040, 2018/06
The J-PARC is a high intensity proton facility and the accelerator consists of a 400 MeV linac, a 3 GeV Rapid Cycling Synchrotron (RCS) and a 30 GeV Main Ring Synchrotron (MR). Regarding 3 GeV beam from the RCS, we delivered it at 150 kW in June 2017 to the materials and life science experimental facility (MLF), for the neutron and muon users. After the replacement of a target, we increased a power up to 500 kW. The beam powers for the neutrino experiment at 30 GeV was 420 kW in May 2016, but increased to 490 kW in April 2018. For the hadron experimental facility which uses a slow beam extraction mode at 30 GeV, we delivered beam at a power of 37 kW, after the recovery from a trouble at an electro static septum in June 2017. But we increased a power to 50 kW in January 2018. We have experienced many failures and troubles to impede full potential and high availability. In this report, operational performance and status of the J-PARC accelerators are presented.
上窪田 紀彦*; 山田 秀衛*; 佐藤 健一郎*; 菊澤 信宏; 山本 昇*; 吉田 奨*; 根本 弘幸*
Proceedings of 16th International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS 2017) (Internet), p.1470 - 1473, 2018/01
J-PARC加速器制御用のネットワークシステムは、2005年以来10年以上運用されてきた。加速器制御ネットワークは、J-PARCの3加速器(リニアック, 3Gevシンクロトロン, MR)と3実験施設(物質・生命科学実験施設,ニュートリノ実験施設,ハドロン実験施設)をカバーし、エッジスイッチの総数は約250である。その全体構成(光ネットワーク網)、冗長機能、VLAN構成、について現状を説明する。次に、オフィスネットワーク(JLAN)と加速器制御ネットワークとの関係について説明する。2つのネットワークの間にFirewallを導入して直接通信を禁止する一方で、双方から制限付きで通信できる別ネットワークを設定した。この手法で、アクセス制限(セキュリティ)と接続性(利便性)の両立を図っている。また、J-PARC加速器制御システムのセキュリティ運用について説明する。オフィスネットワークからのウィルス感染を防ぐための複数のアクセス制限や、アンチウィルスソフトの端末への適用状況について解説する。
長谷川 和男; 金正 倫計; 小栗 英知; 山本 風海; 林 直樹; 山崎 良雄; 内藤 富士雄*; 堀 洋一郎*; 山本 昇*; 小関 忠*
Proceedings of 14th Annual Meeting of Particle Accelerator Society of Japan (インターネット), p.1317 - 1321, 2017/12
J-PARCでは2016年の夏季メンテナンス終了後、加速器の立ち上げや調整を経て、10月下旬からニュートリノ実験施設(NU)、11月上旬から物質・生命科学実験施設(MLF)の利用運転を再開した。NUでは、前回の利用の終了時点(2016年5月)で420kWの出力であったが、チューンの変更や多くのパラメータの最適化調整により、2017年1月には450kW、2月に470kWまで向上した。一方ハドロン実験施設(HD)に向けて2017年4月に調整運転を開始したが、静電セプタムの不具合により停止し、復旧作業により再開し37kWで供給した。MLFでは、2016年度の2回の中性子標的の不具合を受け、新しい設計で標的を製作中であり、それが納入される2017年夏までは150kWのシングルバンチで供給した。2016年度全体では、リニアック、3GeVシンクロトロン(RCS)、MLFともに安定に運転ができ、稼働率は93%であった。一方メインリング(MR)では、小動物のトランスへの侵入や、性能向上に向けた新しい電源の使用開始に伴うノイズによる不具合などがあり、NU向けで約77%、ハドロン向けで約84%の稼働率であった。本発表では、こうしたJ-PARC加速器の運転状況について報告する。
長谷川 和男; 林 直樹; 小栗 英知; 山本 風海; 金正 倫計; 山崎 良雄; 内藤 富士雄*; 小関 忠*; 山本 昇*; 堀 洋一郎*
Proceedings of 8th International Particle Accelerator Conference (IPAC '17) (Internet), p.2290 - 2293, 2017/06
J-PARC加速器は400MeVリニアック、3GeVシンクロトロン(RCS)、30GeVメインリングシンクロトロン(MR)から構成される。リニアックでは入射部の交換やエネルギーの増強、シンクロトロンでは真空の向上やコリメータの能力増強など、多くのハードウェアの性能向上を行ってきた。MRからニュートリノ実験やハドロン実験向けのビーム出力は、加速器調整やビームロス低減によって着実に向上してきた。RCSからは設計値である1MW相当のビーム加速に成功し、中性子やミュオン向けには500kWで利用運転に提供した。一方で、多くの故障や不具合もあり、これらを解決して高い稼働率を目指している。ここでは、こうしたJ-PARC加速器の性能や状況について報告する。
上窪田 紀彦*; 菊澤 信宏; 田村 文彦; 山本 昇*
Proceedings of 15th International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS 2015) (Internet), p.988 - 991, 2016/01
J-PARCのビームコミッショニングが2006年に開始されて以降、タイミングシステムはJ-PARC加速器の安定運転に貢献してきた。タイミングシステムはリニアックおよびRCSの25HzとMRの2.48-6.00秒の2つの異なる周期を統括している。加えて、MLF実験施設とニュートリノ実験施設もしくはMLFとハドロン実験施設の2つの実験施設にビームを供給することが可能である。近年、新しく核変換実験施設の建設が計画されており、主要繰り返しが25Hzから50Hzへと上がり、ビームの供給施設も3施設へと増えることになるため、タイミングシステムのアップグレードも議論されている。8年間の運転実績から得られた知見とアップグレードに関する現在の状況を報告する。