Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Hu, F.-F.*; Qin, T.-Y.*; Ao, N.*; 徐 平光; Su, Y. H.; Parker, J. D.*; 篠原 武尚; 菖蒲 敬久; Kang, G.-Z.*; Ren, M.-M.; et al.
Journal of Traffic and Transportation Engineering, 25(2), p.75 - 93, 2025/04
To accurately predict the remaining lifetime of surface-strengthened railway axles, a damage tolerance method considering three-dimensional (3D) residual stresses was proposed. By taking the induction-hardened carbon steel S38C axle as an example, two-dimensional (2D) distribution characterization of residual strain and 3D residual stress measurement were performed through comprehensive application of the neutron Bragg-edge transmission imaging and angle-dispersive neutron diffraction experiments. A numerical method was employed to implant the 3D residual stress into the axle model, and the remaining lifetime of the full-scale axle was studied by coupling the measured load spectrum, press-fit loads, and residual stresses. Experimental results shows that, both axial and hoop directions present a compressive residual strain gradient layer of about 3 mm, with a maximum compressive residual strain of up to -4500 in the surface layer, yet a maximum tensile strain of up to 1000
in the core. The maximum axial and hoop compressive stresses of the axle are about -500 MPa and -303 MPa respectively, while radial stresses overall fluctuate in the zero mean stress range. At depths beyond 4.5 mm from the surface layer, all three components are tensile stresses. The axle surface layer is subjected to compressive residual stresses, and crack propagation does not occur if the crack depth is less than 4.5 mm. Nevertheless, cracks propagate accelerates when the crack depth is greater than 4.5 mm. Different crack propagation depth thresholds lead to a larger calculated remaining lifetime for the residual stress-free condition than for the case where 3D residual stresses are taken into account. However, the axle remaining service mileage of the axle of 227000 Km under the most conservative conditions exceeds 3.5 non-destructive inspection (NDI) cycles, with a large safety margin. The experimental results can provide a scientific reference for the development and optimization of NDI cycles for surface-strengthened railway axles.
Sans-Planell, O.*; 篠原 武尚; Grazzi, F.*; Cantini, F.*; Su, Y. H.; 松本 吉弘*; Parker, J. D.*; Manke, I.*
Review of Scientific Instruments, 95(11), p.113702_1 - 113702_5, 2024/11
被引用回数:0 パーセンタイル:0.00(Instruments & Instrumentation)This study presents a significant development in the Energy-Resolved Neutron Imaging System RADEN, in the Japan Proton Accelerator Research Complex, Japan. Through a systematic study, the collimation power of the facility was reevaluated. To perform the calculation of the L/D factor of the beam, a state-of-the-art method has been used, along with a standard reference sample to measure the resolution of neutron images. To add robustness to the results, the study compares five different scintillators of different composition and thickness.
渡辺 賢一*; 須貝 優介*; 長谷川 創大*; 田中 清志朗*; 人見 啓太朗*; 野上 光博*; 篠原 武尚; Su, Y. H.; Parker, J. D.*; Kockelmann, W.*
Scientific Reports (Internet), 14, p.25224_1 - 25224_13, 2024/10
被引用回数:0 パーセンタイル:0.00(Multidisciplinary Sciences)Thallium bromide (TlBr) semiconductor detectors are being developed as promising candidates for high-detection-efficiency, high-energy-resolution, and room-temperature gamma-ray spectrometers. This study presents methods for evaluating TlBr crystal quality and carrier transport characteristics using neutron Bragg-dip imaging and the time-of-flight method for pulsed-laser-induced carriers, respectively. In this study, two samples obtained from both the upstream and downstream region in the crystal ingot were evaluated.
社本 真一; 山内 宏樹; 飯田 一樹*; 池内 和彦*; 金子 耕士; Chen, Y.-S.*; 矢野 真一郎*; Hsu, P.-T.*; Lee, M. K.*; Hall, A. E.*; et al.
Physical Review Research (Internet), 6(3), p.033303_1 - 033303_7, 2024/09
MnRhSiの磁気励起は少なくとも0.3から140meVに広がる。200Kでの非弾性散乱強度を積分することで、Mnサイト当たり約5
の磁気モーメントは、約5
であることがわかった。一方で、長距離磁気秩序の磁気モーメントは4Kでわずか2.61
であり、多くの部分が低温まで揺らいでいることがわかった。
Hu, F. F.*; Qin, T. Y.*; Ao, N.*; Su, Y. H.; Zhou, L.*; 徐 平光; Parker, J. D.*; 篠原 武尚; Chen, J.*; Wu, S. C.*
Engineering Fracture Mechanics, 306, p.110267_1 - 110267_18, 2024/08
被引用回数:2 パーセンタイル:55.14(Mechanics)Non-destructive and quantitative mapping of gradient residual strain distribution in surface-hardened railway S38C axles could provide a positive reference for determining service lifetime and maintenance strategy. To tackle this concern, time-of-flight neutron Bragg-edge transmission imaging was employed by real axle samples with and without impacted crater. A novel and simple procedure to formulate the residual strain field was also developed in this work, with the transmission batch code in Appendix A. By mapping the global two- dimensional residual strains, it can be verified that the residual strains into the axle are uniformly distributed in the hoop direction. Subsequently, it was revealed that the axial and hoop residual strains, respectively in the cylinder and the long strip samples prepared from a real S38C hollow axle, indicated a gradient evolution distribution with a depth of 8 mm, covering a range of -5500
1000
for axial strains and -6500
1000
for hoop strains. More importantly, the maximum compressive lattice strain of the cylinder sample was increased by 15.61%, and 22.35% at the impacting speeds of 100, and 125 m/s, respectively; and that of the long strip sample increased by 29.17%, and 43.70%, respectively. It can thus be concluded that lattice strains have redistributed around the impact crater, demonstrating the local alteration of the residual strain field. These new findings suggest the localized variation in residual strains should be taken into account while evaluating the service damage evolution of railway axles, especially those affected by high-speed impacts during operation.
Zhou, L.*; Zhang, H.*; Qin, T. Y.*; Hu, F. F.*; 徐 平光; Ao, N.*; Su, Y. H.; He, L. H.*; Li, X. H.*; Zhang, J. R.*; et al.
Metallurgical and Materials Transactions A, 55(7), p.2175 - 2185, 2024/07
被引用回数:3 パーセンタイル:70.74(Materials Science, Multidisciplinary)High-speed railway S38C axles undergo surface induction hardening for durability, but are susceptible to fatigue cracks from foreign object impact. The neutron diffraction method was employed to measure the residual strain in S38C axles, obtaining microscopic lattice distortion data, for the gradient layer at a depth of 8 mm under the surface. The results showed that after induction-hardening, the microscopic lattice distortion had a gradient distribution, decreasing with the distance from the surface. However, in the case of impacting speed of 600 km/m, the average microscopic lattice distortion increased with the distance from the surface, reaching a maximum augmentation of 55 pct. These findings indicate a strong experimental basis, and improve our understanding of the relationship between macroscopic residual stress and decision-making, in regard to operation and maintenance.
山内 宏樹; Sari, D. P.*; 安井 幸夫*; 坂倉 輝俊*; 木村 宏之*; 中尾 朗子*; 大原 高志; 本田 孝志*; 樹神 克明; 井川 直樹; et al.
Physical Review Research (Internet), 6(1), p.013144_1 - 013144_9, 2024/02
-Mn-type family alloys Mn
have three-dimensional antiferromagnetic (AFM) corner-shared triangular network. The antiferromagnet Mn
RhSi shows magnetic short-range order (SRO) over a wide temperature range of approximately 500 K above the N
el temperature
= 190 K. Mn
CoSi has the smallest lattice parameter and the lowest
in the family compounds. The quantum critical point (QCP) from AFM to the quantum paramagnetic state is expected near a cubic lattice parameter of 6.15
of Mn
CoSi is only 140 K, quantum critical behavior is observed in Mn
CoSi as the enhancement of the electronic specific heat coefficient
. We study how the magnetic SRO appears in Mn
CoSi by using neutron scattering,
SR, and physical property measurements. The experimental results show that the neutron scattering intensity of the magnetic SRO does not change much regardless of the suppressed magnetic moment in the long-range magnetic ordered state compared to those of Mn
RhSi. The initial asymmetry drop ratio of
SR above
becomes small, and the magnetic SRO temperature
is suppressed to 240 K. The results suggest that the Mn
CoSi is close to the QCP in the Mn
system.
渡辺 賢一*; 須貝 優介*; 長谷川 創大*; 人見 啓太朗*; 野上 光博*; 篠原 武尚; Su, Y. H.; Parker, J. D.*; Kockelmann, W.*
Sensors and Materials, 36(1), p.149 - 154, 2024/01
被引用回数:2 パーセンタイル:62.29(Instruments & Instrumentation)Thallium bromide (TlBr) semiconductor detectors are promising candidates for high-detection-efficiency, high-energy-resolution, and room-temperature gamma-ray spectrometers. In this study, we conducted neutron Bragg dip and electron backscatter diffraction (EBSD) imaging of TlBr crystals to measure the crystal orientation distribution. We confirmed that crystal grains were continuous over a certain distance along the solidification direction for samples fabricated with the current growth procedure.
伊藤 あずさ; Karmaoui, M.*; Thirunavukkarasu, G.*; Hriljac, J. A.*
APL Materials (Internet), 11(4), p.041105_1 - 041105_9, 2023/04
被引用回数:4 パーセンタイル:25.54(Nanoscience & Nanotechnology)Composites of zeolite Na-chabazite particles with attached superparamagnetic nanoparticles of FeO
and CoFe
O
ferrite spinels have been produced using a novel solvothermal route. These have been characterized by a combination of techniques including powder X-ray diffraction, X-ray fluorescence spectroscopy, Raman spectroscopy, vibrating sample magnetometry and both scanning and transmission electron microscopy. These confirm the nature of the attached nanoparticles and the microscope images show a good dispersion of nanoparticles with a narrow size range deposit uniformly on the surface of the zeolite particles. The magnetisation is of sufficient strength to allow magnetic separation from solution. Both time and pH dependent Cs uptake experiments show the magnetised systems are still excellent for the rapid uptake of Cs via an ion exchange process with no reduction in property due to the attached nanoparticles.
Zhang, H.*; Wu, S. C.*; Ao, N.*; Zhang, J. W.*; Li, H.*; Zhou, L.*; 徐 平光; Su, Y. H.
International Journal of Fatigue, 166, p.107296_1 - 107296_11, 2023/01
被引用回数:19 パーセンタイル:84.17(Engineering, Mechanical)Abnormal damages in railway axles can lead to a significant hazard to running safety and reliability. To this end, a surface treatment was selected to effectively inhibit fatigue crack initiation and growth. In this study, a single edge notch bending fatigue test campaign with artificial notches was conducted to elucidate the fatigue crack non-propagation behavior in railway S38C axles subjected to an induction hardening process. The fatigue cracking behavior in the gradient structure was revealed by optical microscopy, electron backscatter diffraction, and fractography. The microhardness distribution was measured using a Vickers tester. The obtained results show that the microhardness of the strengthening layer is nearly triple that of the matrix. Owing to the gradient microstructures and hardness, as well as compressive residual stress, the fatigue long crack propagates faster once it passes through the hardened zone (approximately 2.0 mm in the radial depth). Thereafter, local retarding (including deflection, branching, and blunting) of the long crack occurs because of the relatively coarse ferrite and pearlite in the transition region and matrix. Totally, this fatigue cracking resistance is reasonably believed to be due to the gradient microstructure and residual stress. These findings help to tailor a suitable detection strategy for maximum defects or cracks in railway axles.
Yan, S. Q.*; Li, X. Y.*; 西尾 勝久; Lugaro, M.*; Li, Z. H.*; 牧井 宏之; Pignatari, M.*; Wang, Y. B.*; Orlandi, R.; 廣瀬 健太郎; et al.
Astrophysical Journal, 919(2), p.84_1 - 84_7, 2021/10
被引用回数:5 パーセンタイル:33.27(Astronomy & Astrophysics)The long-lived Fe (with a half-life of 2.62 Myr) is a crucial diagnostic of active nucleosynthesis in the Milky Way galaxy and in supernovae near the solar system. The neutron-capture reaction
Fe(n,
)
Fe on
Fe (half-life=44.5 days) is the key reaction for the production of
Fe in massive stars. This reaction cross section has been previously constrained by the Coulomb dissociation experiment, which offered partial constraint on the E1
-ray strength function but a negligible constraint on the M1 and E2 components. In this work, for the first time, we use the surrogate ratio method to experimentally determine the
Fe(n,
)
Fe cross sections in which all the components are included. We derived a Maxwellian-averaged cross section of 27.5
3.5 mb at
= 30 keV and 13.4
1.7 mb at
= 90 keV, roughly 10%-20% higher than previous estimates. We analyzed the impact of our new reaction rates in nucleosynthesis models of massive stars and found that uncertainties in the production of
Fe from the
Fe(n,
)
Fe rate are at most 25
. We conclude that stellar physics uncertainties now play a major role in the accurate evaluation of the stellar production of
Fe.
Parker, J. D.*; 原田 正英; 林田 洋寿*; 廣井 孝介; 甲斐 哲也; 松本 吉弘*; 中谷 健; 及川 健一; 瀬川 麻里子; 篠原 武尚; et al.
Materials Research Proceedings, Vol.15, p.102 - 107, 2020/05
At the RADEN instrument, we take advantage of the accurate measurement of neutron energy by time-of-flight to perform energy-resolved neutron imaging using event-type neutron imaging detectors. We are continually working to improve these detectors for better spatial resolution and shorter measurement times and, as a user facility, to improve the ease-of-use of their control and analysis software. In particular, we are actively developing a He-based gaseous micropattern detector known as the Micro-pixel chamber based Neutron Imaging Detector (
NID). We have recently redesigned the
NID control software to allow full integration into the automated experiment control system at RADEN, and we are carrying out optimization of the analysis algorithms for improved image quality and rate performance.
篠原 武尚; 甲斐 哲也; 及川 健一; 中谷 健; 瀬川 麻里子; 廣井 孝介; Su, Y. H.; 大井 元貴; 原田 正英; 飯倉 寛; et al.
Review of Scientific Instruments, 91(4), p.043302_1 - 043302_20, 2020/04
被引用回数:79 パーセンタイル:97.38(Instruments & Instrumentation)The energy-resolved neutron imaging system, RADEN, has been installed at the pulsed neutron source in the Materials and Life Science Experimental Facility of the Japan Proton Accelerator Research Complex. In addition to conventional neutron radiography and tomography, RADEN, the world's first imaging beam-line at a pulsed neutron source, provides three main options for new, quantitative neutron imaging techniques: Bragg-edge imaging to visualize the spatial distribution of crystallographic information, resonance absorption imaging for elemental composition and temperature information, and polarized neutron imaging for magnetic field information. This paper describes the results of characterization studies of the neutronic performance and installed devices at RADEN and shows the results of several demonstration studies for pulsed neutron imaging.
甲斐 哲也; 廣井 孝介; Su, Y. H.; 瀬川 麻里子; 篠原 武尚; 松本 吉弘*; Parker, J. D.*; 林田 洋寿*; 及川 健一
Materials Research Proceedings, Vol.15, p.149 - 153, 2020/02
A two-dimensional thermometry technique based on neutron resonance reactions derives the temperature of specified elements in an object by analyzing the Doppler broadening of a neutron resonance measured by a time-analyzing neutron imaging-detector. This technique is expected to be one of the important applications of the energy-resolved neutron imaging system, RADEN, at J-PARC. The authors focused on molybdenum contained in 316 stainless-steel (with a weight fraction of 2-3 wt%). Energy-dependent transmitted neutrons were measured through a 3 mm thick 316 stainless-steel plate placed in a heater at temperatures between 23 and 500 degrees Celsius at RADEN using a gas-electron multiplier (GEM) detector. Thermal and cold neutrons were eliminated from the incident beam by a cadmium filter. The sample area within the neutron beam was 30 by 50 mm. The feasibility is discussed in the presentation.
小野 章*; Xu, J.*; Colonna, M.*; Danielewicz, P.*; Ko, C. M.*; Tsang, M. B.*; Wang, Y,-J.*; Wolter, H.*; Zhang, Y.-X.*; Chen, L.-W.*; et al.
Physical Review C, 100(4), p.044617_1 - 044617_35, 2019/10
被引用回数:75 パーセンタイル:98.53(Physics, Nuclear)2017年4月に開催された国際会議Transport2017において、重イオン核反応モデルの国際的な比較が議論された。重イオン加速器の安全評価や宇宙飛行士の被ばく評価等で重要な役割を果たすため、世界中で重イオン核反応の様々な理論モデルが開発されている。本研究では、辺の長さが20fmの直方体に320個の中性子と陽子をランダム配置し、それらが70fm/cの間に起こす散乱の回数やエネルギーを計算した。ここでは、特にパイオンやその前駆体であるデルタ共鳴の生成に注目して比較を行った。参加コードは、個々の粒子の時間発展を追うQMD型コードと、粒子の位置や運動量の確率分布を決めておき、散乱や崩壊が発生したときそれらを乱数サンプリングするBUU型コードがあり、発表者が用いたJQMDは前者に属する。本研究により、計算における時間刻みが各コードによる結果の差の主な原因であることが分かった。さらに、今後のJQMDの改良方針の策定に有益な知見を得ることができた。
Bandodkar, A. J.*; Gutruf, P.*; Choi, J.*; Lee, K.-H.*; 関根 由莉奈; Reeder, J. T.*; Jeang, W. J.*; Aranyosi, A. J.*; Lee, S. P.*; Model, J. B.*; et al.
Science Advances (Internet), 5(1), p.eaav3294_1 - eaav3294_15, 2019/01
被引用回数:566 パーセンタイル:99.88(Multidisciplinary Sciences)非侵襲でバイオマーカーを検出し得るウェアラブルデバイスが注目されている。しかしながら現在までに存在するウェアラブルデバイスはその電力源や検出部分などの小型化が困難であったことから重さや大きさの点でポータビリティに欠けていた。本研究では、バッテリーフリーでかつ電気的、呈色式を用いて重要バイオマーカーである塩化物, 乳酸, グルコース, pHを検出できるスウェットデバイスを開発した。
及川 健一; Su, Y. H.; 鬼柳 亮嗣; 川崎 卓郎; 篠原 武尚; 甲斐 哲也; 廣井 孝介; Harjo, S.; Parker, J. D.*; 松本 吉弘*; et al.
Physica B; Condensed Matter, 551, p.436 - 442, 2018/12
被引用回数:6 パーセンタイル:26.43(Physics, Condensed Matter)We are promoting for practical product observation by the energy-resolved neutron imaging method using high-intensity pulsed neutrons at J-PARC, under the Photon and Quantum Basic Research Coordinated Development Program from the Ministry of Education, Culture, Sports, Science and Technology, Japan. Bragg edge imaging, one of the energy-resolved neutron imaging methods for visualizing material properties, was applied to feasibility study of the temperature distribution of copper rod, complementary study of the texture and strain distribution of bent steel plates using neutron diffraction and EBSD, and so on. Outline of results obtained by these imaging experiments will be presented.
甲斐 哲也; 佐藤 節夫*; 廣井 孝介; Su, Y. H.; 瀬川 麻里子; Parker, J. D.*; 松本 吉弘*; 林田 洋寿*; 篠原 武尚; 及川 健一; et al.
Physica B; Condensed Matter, 551, p.496 - 500, 2018/12
被引用回数:4 パーセンタイル:17.88(Physics, Condensed Matter)The 2012 model lithium-6 time-analyzer neutron detector (LiTA12) system, based on a lithium glass scintillator and multi-anode photomultiplier tube, has the highest neutron efficiency among the detectors for pulsed neutron imaging together with a flexibility of the efficiency by changing the thickness of the lithium glass. The authors expect this detector system could become a main detector system for the energy-resolved neutron imaging system, RADEN, at J-PARC, and have started evaluation of the LiTA12 system. For example, spatial resolution for resonance absorption imaging was evaluated by using a line-pair pattern made by 3 micro meter thick gold on a quartz plate. Less than 1 mm width line pairs were resolved at an 8 Mcps neutron counting rate and around 5 eV neutron energy.
廣井 孝介; 篠原 武尚; 林田 洋寿*; Parker, J. D.*; Su, Y. H.; 及川 健一; 甲斐 哲也; 鬼柳 善明*
Physica B; Condensed Matter, 551, p.146 - 151, 2018/12
被引用回数:8 パーセンタイル:34.08(Physics, Condensed Matter)Grain oriented magnetic steel is widely used as a key material for magnetic industrial products. Since magnetic properties of steels are closely related to its magnetic domain structure, observation of the domain structure is important for understanding its magnetic properties. In this study, we attempted to observe the domain structure of a grain oriented steel using polarized pulsed neutron imaging. In the experiment, we first magnetized the sample by applying a magnetic field along the easy-to-magnetize direction via a coil, and confirmed the sample was magnetized almost uniformly from the obtained polarization distribution images. By analyzing the oscillatory behavior in the wavelength dependence of polarization, magnetization of the steel was estimated to be 1.82 T. Then, we removed the field and performed the same measurement. As a result, a striped domain structure was observed, with neighboring domains aligned anti-parallel to each other. From these results, it was demonstrated that our magnetic imaging method could visualize the magnetization and the direction of the domains in the practical steel.
廣井 孝介; 篠原 武尚; 林田 洋寿*; Parker, J. D.*; 及川 健一; Su, Y. H.; 甲斐 哲也; 鬼柳 善明*
JPS Conference Proceedings (Internet), 22, p.011030_1 - 011030_7, 2018/11
We have been developing magnetic imaging method for industrial products using polarized pulsed neutrons. In this presentation, we report observation results of magnetic field distribution in a small electric transformer as a demonstration of our magnetic imaging method. The polarized pulsed neutron imaging experiment was performed at BL22 RADEN at MLF of J-PARC. 9 polarization distribution images were obtained with changing incident polarization and analyzing direction in 3D. By analyzing wavelength dependent polarization position by position, distribution of field strength and direction around the core of the transformer were successfully visualized. Obtained field distribution images were well corresponded with that expected by the simulation and clearly demonstrated a leaked field from the gap of step lap.